HBA/RAID controller

HBA, RAID and SAS Expander

• HBA is just a controller that provides an expansion of SAS/SATA ports. What manages the drives is up to the OS.
• A RAID Controller is like an HBA but has the onboard functionality to create a array which is then presented to the OS as a singular drive
• SAS Expanders can be used to maximize the # of storage capability of your HBA or SAS controller card. SAS expanders can be used with RAID controllers and SAS HBAs.

Native and Maximum supported disks

There is a concept in RAID controller, that are Native Supported Disks and Maximum Supported Disks.

• Native supported disk # means the number of disks that can be direct connected to the RAID controller using brakeout cable
• Maximum supported disks # means when to use of port expanders such as Intel RES2SV240

Controller Interface

The RAID controller has an interface that connects to the storage drive and an interface that connects to the

CPU. The drive interfaces are Serial Attached SCSI (SAS), Serial Advanced Technology Attachment (SATA),

and Non-Volatile Memory Express (NVMe). NVMe is a communication protocol designed for flash storages

that use Peripheral Component Interconnect Express (PCIe) for connectivity.

Storage drive side interface	Communication band	Theoretical throughput	Effective throughput (90%)
SATA 6G	6 Gbps	572 MiB/s	515 MiB
SAS 12G	12 Gbps	1,144 MiB/s	1,030 MiB/s
NVMe Gen3	8 Gbps x4	3,756 MiB/s	3,380 MiB/s
NVMe Gen4	16 Gbps x4	7,512 MiB/s	6,760 MiB/s

CPU side Interface	Number of lanes	Communication band	Theoretical throughput	Effective throughput (90%)
DMI Gen3	x4	8 Gbps x4	3,756 MiB/s	3,380 MiB/s
PCIe Gen3	x8	8 Gbps x8	7,512 MiB/s	6,760 MiB/s
PCIe Gen3	x16	8 Gbps x16	15,024 MiB/s	13,520 MiB/s
PCIe Gen4	x8	16 Gbps x8	15,024 MiB/s	13,520 MiB/s
PCIe Gen4	x16	16 Gbps x16	30,048 MiB/s	27,040 MiB/s

*The theoretically achievable throughput is calculated by subtracting 1.54% redundancy with 128b/130b coding.

The actual achievable throughput can be estimated by multiplying this value by 0.90.

Expected Performance by RAID type

RAID level	Type	Random read	Random write	Sequential read transfer performance	Sequential write transfer performance	Features
RAID0	Stripe	1	1	N x SR	N x SW	Ideal for applications that require high bandwidth but do not require fault tolerance
RAID1	Mirror	1	2	N x SR	N x SW / 2	Ideal for any application that requires fault tolerance and minimal capacity.
RAID10	Mirror + Stripe	1	2	N x SR	N x SW / 2	Ideal for fault tolerance
RAID5	Single Parity	1	4	N x SR	(N-1) x SW	Idle for fault tolerance with limited overhead
RAID50						support to sustain one drive failure per RAID 5 drive group and still maintain data integrity
RAID6	Double Parity	1	6	N x SR	(N-2) x SW	Idle for fault tolerance with limited overhead Not well suited to tasks requiring lot of writes due to two sets of parity data for each write operation.
RAID60						support to sustain two drive failures per RAID6 drive group and still maintain data integrity
Where, N: Number of drives, SR: Single read performance, SW: Single write

RAID Configuration Strategies

You cannot configure a virtual drive that optimizes all three factors, but it is easy to choose a virtual drive configuration that maximizes one factor at the expense of another factor

Purpose	Strategies	Spare drives
Virtual drive availability (fault tolerance)	RAID 1 (mirroring) provides excellent fault tolerance, but requires a redundant drive	The hot spare automatically takes its place and the data on the failed drive is rebuilt on the hot spare. Hot spares can be used for RAID levels 1, 5, 6, 10, 50, and 60.
Virtual drive performance	RAID 0 (striping) offers excellent performance RAID 00 (striping in a spanned drive group) offers excellent performance RAID 5 provides high data throughput, especially for large files RAID 6 works best when used with data that requires high reliability, high request rates, and high data transfer. It provides high data throughput, data redundancy, and very good performance. However, RAID 6 is not well suited to tasks requiring a lot of writes.
Virtual drive capacity	RAID 0 provides maximum storage capacity for a given set of drives

Performance Index - Throughput / Transaction

• Throughput [MiB/s] - Data transfer amount per second (in megabytes)
• Transaction [IO/s] - IO processing per second
• Latency [ms] - Average response time (in milliseconds)

"Data Throughput” value used to load profiles with sequential access pattern, while “Transaction Rate”

value used to load profiles with random access pattern. Throughput and transaction are in direct

proportion to each other and can be calculated mutually using the follow

• Data throughput [KiB/s] = Transaction rate [IO/s] x Block size
• Transaction rate [IO/s] = Data throughput [KiB/s] / Block size [KiB]

Controller information on Linux

# Find controller information
$sudo lspci -vv | grep -i raid

# Find raid has been configured or not and check the output
$cat cat /proc/scsi/scsi